热门关键词搜索: 润滑油工业润滑油 润滑油厂家

您的当前位置:主页 > 新闻资讯 > 常见问题 >

导热油厂家介绍导热油使用的注意事项

来源:www.jnkangpeng.com 编辑者:康鹏润滑油 发布日期:[2017-07-11 14:17] 浏览:|

  导热油厂家介绍导热油使用的注意事项:

  Heat conduction oil factory introduces the precautions of heat conduction oil:

  1、运行中严禁超温使用,确保导热油的正常使用寿命。

  1, the operation is strictly prohibited overheating use, to ensure the normal service life of heat conduction oil.

  2、按导热油的牌号及用热工艺要求,正确选用各种牌号节能导热油,并严格各项规定,正确使用导热油。

  2, according to the heat transfer oil grade and the thermal process requirements, correctly select all kinds of energy-saving heat conduction oil, and strict regulations, the correct use of heat transfer oil.

  3、在使用中应认真检查,严防水、酸、碱及低沸点物漏入使用系统,并加装过滤装置,防止机械杂物进入,确保油品纯度

  3, in use, should be carefully checked to prevent water, acid, alkali and low boiling point leakage into the use of the system, and the installation of filtering devices to prevent the entry of mechanical debris, to ensure purity of oil

  4、节能导热油适用于燃煤、燃气、燃油加热热炉作载热体,电加热反应釜等供热设备使用时,应具有膨胀槽和贮槽及其它安全组件和温控仪表等配套设施,确保安全运行。

  4, energy-saving heat conducting oil used as heat carrier to coal, gas and oil heating furnace, electric heating reactor and other heating equipment used, should be expanded and tank and other security components and temperature control instrumentation and other facilities, to ensure safe operation.

  5、凡旧供热设备更换新导热油时,必须消除内壁杂物,以免影响导热油的传热效率和使用寿命。

  5, where the old heating equipment replacement of new heat transfer oil, you must eliminate debris on the wall, so as not to affect the heat transfer oil efficiency and service life.

  6、高温导热油经使用半年后,应进行一次油品分析。若长期使用后,发现传热效果差、或发现异常情况,应根据油品分析结果决定(主要控制项目,残炭不大于1.5℅,酸值不大于0.5mgKOH/g,闪点变化不大于20℅,粘度变化不大于15℅)若其中一项不合格时应考虑添加部分新油或全部更换新油。

  6, high temperature heat transfer oil after six months, should be a oil analysis. If used for a long time, it is found that the heat transfer effect is poor, or the abnormal situation, should be decided according to the oil analysis (mainly carbon residue control project, not more than 1.5 percent, the acid value is less than 0.5mgKOH/g, the change of the flash point of not more than 20 percent, the viscosity change is not greater than 15 percent) if one is not qualified should be considered when adding some new oil or oil to replace all.

  7、导热油投入使用,在开始运行时先启动循环油泵运行半小时后,再点火升温,在初次使用时应缓慢升温每小时20℃,当温度升至130℃左右时,要保温一段时间,当温度升至180℃-200℃时再保温一段时间后方可投入正常使用。

  7, oil is put into use, at the start of operation to start the pump running after half an hour, and then the ignition temperature, is used for the first time should be slow to warm up every hour 20 degrees, when the temperature rose to 130 degrees Celsius, to be preserved for a period of time, when the temperature rise to 180 DEG -200 DEG again when the holding time behind can be put into normal use.

同类文章:

文章标题:导热油厂家介绍导热油使用的注意事项

推荐阅读/ Recommended reading

我们都知道 润滑油 的作用是用来降低发动机零件的磨损,延长使用寿命,同样,只有质量好的润滑油才能起到这些作用,反之还会伤害发动机。再好的润滑油都有它自己的使用寿命,...

导热油的热稳定性及其测评方法[2017-12-07]
润滑油中进水了该如何做?[2017-09-28]
工业润滑油使用操作规范[2017-11-27]
液压油多久更换?如何判断液压油是否要[2018-01-15]
润滑油专业生产,做大家放心的产品[2018-04-16]
如何识别真假润滑油[2018-01-25]
哪些情况下润滑油会导电?[2017-06-23]
润滑油厂家告诉你什么是全合成润滑油[2018-07-23]
润滑油的粘度越大越好么?[2018-10-12]
石油产品的分类级相关最新标准[2017-12-01]
  • 扫一扫,访问手机站